How To Remove Soldered Copper Pipe

Removing a copper pipe that has been soldered in place can be a difficult task. The most common method is to use a propane torch to heat the solder joint until it liquefies. Then, using a plunger, you can try to remove the copper pipe. If the pipe is still stuck, you can use a hacksaw to cut the pipe below the solder joint and then use a plunger to remove the piece of pipe that was cut off.

How To Remove Soldered Copper Pipe

Removing a section of copper pipe that has been soldered in place can be a difficult task. The most important thing to remember is not to damage the pipe while trying to remove it. There are a few different ways to go about removing a soldered copper pipe. One way is to use a blow torch. Heat the solder around the pipe until it is melted. Then use a pair of pliers to pull the pipe out. Another way is to use a hacksaw to

-copper pipe -soldering iron -solder – flux -tin snips

  • Apply heat to the soldered joint until it liquefies
  • Thread a wire through the hole and twist the ends together to form a makeshift clamp
  • Use a drill with a metal bit to drill through the copper pipe

below – use a heat gun or propane torch to heat the solder – use a plunger to create suction and pull the pipe out – use a drill with a wire brush attachment to clean the remaining solder


Frequently Asked Questions

How Do I Remove A Stubborn Solder Copper Pipe?

You could use a hacksaw to cut the pipe, and then use a chisel or pliers to remove the solder.

Can You Unsweat A Copper Fitting?

Theoretically, it is possible to unsweat a copper fitting; however, it would be a difficult and time-consuming process. The fittings would need to be heated until they are red-hot, and then the water would need to be slowly poured over them until the fitting was cool enough to touch. Even then, there may be residual water trapped inside the fitting, which could cause corrosion.

How Do You Release A Soldered Pipe?

There are a few ways to release a soldered pipe. One way is to use a propane torch to heat the solder until it liquefies. Once the solder is liquefied, you can use a plunger to push the solder out of the pipe. Another way to release a soldered pipe is to use a hacksaw to cut the pipe above the solder joint.

How Do You Take Apart A Soldered Copper Pipe Fitting?

To take apart a soldered copper pipe fitting, use a hacksaw to cut the pipe as close to the fitting as possible. Use a pipe wrench to twist the fitting off the pipe.

How Do You Resweat A Copper Fitting?

You can resweat copper fittings using a propane torch. Heat the fitting until the solder melts, then use a flux brush to coat the fitting and the solder. Hold the solder against the fitting and use the torch to heat it until the solder flows.

How Do You Remove Soldered Valves?

To remove a soldered valve from a pipe, you need to heat the solder until it is liquid and then use a plunger-type tool to pull the valve free.

How Do You Loosen Old Copper Pipe Fittings?

One way to loosen old copper pipe fittings is to use a wrench. Another way is to use a propane torch.

Can You Resolder Copper Pipe?

Yes, you can resolder copper pipe. It is a common plumbing repair that can be done using a few simple tools. First, make sure the pipe is clean and free of any debris. Next, apply flux to the soldering iron and the end of the pipe. Finally, hold the soldering iron against the pipe and solder the joint.

How Do You Remove Sweated Copper Fittings?

Removing sweated copper fittings can be done using a number of methods. One way is to use a propane torch to heat the fitting until the solder melts. Once the solder has melted, the fitting can be gently wiggled loose and then removed. Another way to remove a sweated copper fitting is by using a wrench. The wrench can be placed on the fitting and then turned in a clockwise motion until the fitting comes loose.

Can I Solder Copper Pipe Without Flux?

A flux is a substance that is applied to metal surfaces to clean them, help with the soldering process, and to prevent oxidation. Copper pipe can be soldered without flux, but it is not recommended as the results may not be as reliable.


To Summarize

Removing a soldered copper pipe is a difficult task that requires patience and precision. First, identify the section of the pipe to be removed and use a hacksaw to cut through the pipe just above the solder joint. Use a file to smooth out the rough edge of the cut. Next, use a propane torch to heat the solder joint until it is melted. Use a pair of pliers to grip the pipe and twist it until it pops loose from the solder joint. Finally, use a wire brush to clean off any residual solder from the pipe.

Posts created 473

Leave a Reply

Your email address will not be published.

Related Posts

Begin typing your search term above and press enter to search. Press ESC to cancel.

Back To Top